- Suits 1-2 rabbits
- Measures 2.3m long, 0.9m wide and 0.7m high
- Made from strong, yet light-weight, aluminium frame
- Strong 2.5mm thick galvanised mesh with 25mm squares
- Made standard with part solid roof, solid back door and two side walls made with zincalume, galvanised mini corrugated iron (Colorbond colours available on upgrade)
- Four access doors – one on either end and two roof lid panels
- Takes 1+ hours to assemble, with detailed illustrated instructions provided
ALUMINIUM FRAMEWORK
Aluminium is much lighter than steel which means less strain for you to move your hutch around your yard. Also, unlike steel or timber, aluminium will not rust or deteriorate in the weather. You can be rest assured that your hutch will be looking just as great in many years time.
Black Frame Optional Upgrade: Rabbit hutches are made standard with silver anodized aluminium framework, however black framework is also available as an optional upgrade.
SMALL-SIZED GALVANIZED MESH
Rabbit Runs are made with small sized galvanised steel mesh, 25mm x 25mm x 2.5mm. This mesh is very strong and is impossible for foxes or dogs to chew through or for you to accidentally damage.
Mini Mesh Optional Upgrade: If you prefer, you can have your hutch made with 12.5mm x 12.5mm mesh that is 1.24mm thick.
MINI FLUTED CORRUGATED IRON
The side walls and roof of the Rabbit Run is made using mini fluted corrugated iron in Zincalume (silver) colour. This is quality Bluescope steel which is made in Australia.
Colorbond Optional Upgrade: The Rabbit Run is also available in Colorbond for Pale Eucalypt, Deep Ocean, Monument and Woodland Grey. Custom Colorbond colours are also available upon request.
FOUR DOORS FOR EASY ACCESS
This hutch has four different doors for easy access to your pets. Both ends of the hutch open downwards. The roof is also made up of two hinged sections, allowing you to open just the housing section roof or just the run section roof to reach your bunnies or guinea pigs.
SUMMER VENTILATION
Royal Rooster hutches are designed and made in Australia, taking into consideration our very hot summers. The whole front of the housing section on the Rabbit Run is open to allow maximum ventilation in the hot summer months. There are also two side ventilation sections on the sides of the enclosure, for extra ventilation in the housing area.
Weather Shield Optional Upgrade: ‘Weather shields’ are an optional extra that can also be purchased to provide extra protection in wet or windy weather. One shield further encloses the housing section with still a gap for the rabbits to enter the housing area. The other two shields go over the side ventilation areas to keep the housing area nice and cosy in the cool weather.
OPEN FLOOR DESIGN
The Rabbit Run hutches have an open floor design as standard. You can then chose if an anti dig mesh floor in needed as well as an optional litter tray for the housing area.
Anti Dig Floor Optional Upgrade: Optional anti dig floors can also be purchased for those needing to prevent their bunnies from digging their way out or for those concerned about foxes digging their way in! These floors come in either sections of 50mm x 50mm mesh that is 3mm thick or the smaller 12.5mm x 12.5mm x 1.24mm mesh.
Litter Tray Optional Upgrade: Make life easier for yourself with an optional litter tray for the housing area of your Rabbit Run. This removable floor is made with an aluminium frame and infilled with aluminium composite panel. This can easily be removed via the rear housing door for easy cleaning on a regular basis.
MOBILE HUTCHES
As these hutches are made with aluminium rather than heavy steel frames, the hutches are easy to move with one person lifting on each end of the enclosure.
Wheel Kit Optional Upgrade: The optional wheel upgrade makes moving your rabbit hutch even easier. Just turn the lever arms into the raised position on either side of your hutch, push or pull your enclosure to a new area and then lower again.
DELIVERY INSURANCE
Highly recommended. This covers the replacement or repair of your hutch if damaged in transit as well as the freight to transport damaged parts back to us and new parts over to you. Only $15 for peace of mind.
ASSEMBLY REQUIREMENTS
These hutches are very simple to put together and come with detailed, illustrated instructions. You’ll need a rubber mallet, an electric drill and a number 2 Philips-head driver. Assembly time should be 1+ hours depending on skill level.
LEAD TIME & FREIGHT
All hutches are made in our purpose built premises in Willaston in South Australia. Lead times on orders can vary depending on the time of the year and other factors out of our control. Please click here to see that latest lead time on orders.
Delivery with TNT generally then takes between 1-2 weeks to arrive. We have both depot pick up and residential delivery as freight options to keep the cost down for those able to collect from a TNT depot or agent.
If you live in SA, pickup from our premises at 43 Theen Ave, Willaston SA 5118 is most welcome.
Not what you’re after? See the whole range of products on offer from Royal Rooster or contact us if you have further questions. We’d love to help!
Reviews
There are no reviews yet.